Bachmann Trains & Accessories

Ho Model Trains Dcc
Can you control the model railroad with a personal computer without a DCC equipped locomotive?

I was wondering if I can control my scale trains O or HO scale model railroad without DCC equipped locomotives. Is there any software and / or hardware out there that allow me to do this? I was thinking that the team might be connected to a regular DC control that alters the power to the track, so you can control the train that way. Is there anything out there that can do this?

Check out this article for answers to your questions http://www.pc-control.co.uk/computrain.htm And this series is incredible – including the start – which is a series 9 and print pdf files A. team train together http://keller-tuberg.homeip.net/ origin ~ stefan / train / index.html Article 1 There's more to trains the model shown in the eyes http://keller-tuberg.homeip.net/ ~ stefan/train/article1.html Article 2 train detection and control of DC motors with a team Article ~ http://keller-tuberg.homeip.net/ stefan/train/article2.html 3 The driver circuit http://keller-tuberg.homeip.net / ~ stefan/train/article3.html Etc. This is a commercial site http://www.freiwald.com/pages/traincontroller.htm HTH Search ╰ ☆ ╮ ☆ 's Please add a note when you vote! ╰ ☆ ╮

Ho Model Trains Dcc

This integral part of the power to gearbox is essential in stabilizing the gearbox and driving the locomotive. This unit is critical depending on the type of locomotive you are going to modify.

Small engines usually have space problems between the can motor drive shaft and the gearbox drive shaft. To solve this dilemma, you have a choice of two means of fastening the two drive shafts together and still maintain stability of the gearbox. One is the old method of using neoprene tubing to act as a drive mechanism and to stabilize the gearbox. The other is a U-Joint and couplings however, this method requires a means to stabilize the gearbox.

Tubing that is available today is far more stable and holds its elasticity far longer than the original tubing. Previously the tubing lost all elasticity and became brittle. On the other hand, U-Joints and couplings work similar to the drive shaft on an automobile. The draw back is when the shaft begins to turn a monetary torque de-stabilization disruption of the rotation of the driveshaft may inhibit the gearbox from operating. The coupling can slip out of its hold due to the torque and the desire of the gearbox to ride up or spins on the main gear.

To compensate for this anomaly, one must find a means to hold the shaft connection steady. One way is to build a bracket with a bearing to be attached to the frame of the locomotive. The shaft of the Can Motor is then inserted into the bearing and the bracket is attached to the frame. Once this is done, the U-Joints and couplings are placed on the Can Motor shaft and the two interfaces, Can Motor shaft and gearbox shaft, is coupled together.

With this method, you must have a means to adjust the couplings so they do not bind. This is usually done by drilling an oblong hole where attachment for the Can Motor was located. This allows the user to move the Can Motor backwards or forwards before tightening the fastener down. However, many times the space between the two shafts is so small the neoprene tubing method is the only means that will work.

The other type of stabilizer is the torque arm. This one is my favorite however, it is complicated. You have to build the torque arm from scratch. The trickiest part of this operation is the drilling and taping of two holes in the gearbox casement. You must be very careful not to penetrate the void in the gearbox casement.

The other part is making the torque arm its self. This requires a 3′ to 4′ x 1/4′ x 1/32′ of brass sheeting. The length of the brass sheeting depends on the size of the area where the torque arm is to be installed. One end is bent up 90 degrees. This end would have two holes drilled to match the two holes on the gearbox encasement.

At the point where the Can Motor would be stationed you would build a bracket with a right angle tab. The bracket would be drilled out to match the Can Motor configuration and the two screw holes in the can motor. The bracket would then be soldered to the torque arm. The end of the torque arm would be equal in length from the gearbox encasement to the end of the can motor.

On the bottom of the torque arm, just beneath were the can motor sits, solder a solid brass shaft of 2mm in diameter and 1/4′ in length. Also, you would solder in place a quarter spring at the same soldering point. Then you would drill an oblong hole in the frame where the original motor attach point was located. This hole will allow the 2mm shaft to ride up and down much like the real torque arm does. The motor is heavy enough to stop the gearbox from trying to spin.

This is, in my opinion, the best stabilizer of them all and keeps the drive mechanism in perfect alignment.

Joy Ball has been involved in the restoration and maintenance of a variety of Brass Model Locomotives. Through her years of expertise, Mrs. Ball has perfected the art of train restoration often spending countless hours preserving vintage Brass Locomotives to running condition of even the newest Brass Model Replicas. It should be noted that the above article was written by JoyÂ’s husband Michael Ball. Receive her free newsletter at http://www.brasslocomotiveworks.com.

HO scale GP-7 is not working properly?

I recently bought a GP-7 HO scale model train a works very slowly and slightly back and forth, I'd like a solution if possible. The man I bought it said was fully available, it could not be DCC? mine is only a design DC (no sound or light control), but it should work well continuous? helpp please!

Could simply be dirty wheel in the engine. If the engine is stored for some time, oxidation could have put to stop the flow of electricity current. Clean the wheels and see if correct the problem.

HO Scale NASA train DCC controlled on 6 X 9 layout.